Trail Blazer: 5 sets of 2:00 on, 1:00 off with ground-to-overhead from heavy to light and max shuttle runs. Target: finish every barbell set with time left to run.
5 Sets · 2:00 On, 1:00 Off
- Set 1: 5 Ground-to-Overhead (255/175 lb), then max No-Touch Shuttle Runs
- Set 2: 7 Ground-to-Overhead (225/155 lb), then max Shuttle Runs
- Set 3: 9 Ground-to-Overhead (185/125 lb), then max Shuttle Runs
- Set 4: 11 Ground-to-Overhead (135/95 lb), then max Shuttle Runs
- Set 5: 13 Ground-to-Overhead (95/65 lb), then max Shuttle Runs
Shuttle runs are 15 ft = 1 rep. Score is total reps. If your clean & jerk max is under 305/205 lb, use 80-70-60-50-40% of your max.
Warm-Up
Plan on about 25–30 minutes. Move through each part in order; the last part is a short rehearsal at workout pace. Tap any underlined movement to watch a demo.
Warm-Up
5:00 AirBike
- Easy, building to moderate
Movement Prep
2 rounds, empty bar
- 8 Barbell RDLs
- 6 Hang Muscle Cleans
- 4 Strict Press
- 20s PNF Elevated Cat on the bar in the rack
Build-Up
3–5 minutes, empty bar
- Practice the exact variation you’ll use (power clean + split jerk, power snatch, etc.)
Rehearsal
5–6 sets, build to the Set 1 weight
- 2–3 Ground-to-Overhead
- 6 Shuttle Runs (15 ft = 1)
Trim reps as you get heavier.
Rest to Recovery, Then Go Get It!
Scaling
Scale so every set leaves at least 45 seconds of shuttle runs.
| Movement | RX | Intermediate | Beginner |
|---|---|---|---|
| Ground-to-Overhead | 255-225-185-135-95 / 175-155-125-95-65 lb | 80-70-60-50-40% of your clean & jerk | 70-60-50-40-30% of your clean & jerk |
| Shuttle Run | Max, 15 ft = 1 | Max | Max (walk-back allowed) |
Intent
Trail Blazer is a descending-load, ascending-rep barbell interval. Heavy and short at the start, light and long at the end, with shuttle sprints filling the rest of each window.
- What it tests: strength under fatigue, barbell cycling and repeat sprint capacity
- Target: finish every barbell set with time left to run
- Good fit for RX if: your clean & jerk is at least 305/205 lb
Strategy
- Heavy sets: fast singles with good setup. Don’t miss reps.
- Light sets: touch-and-go or quick singles, then run hard.
- Shuttles: stay low at the turns and don’t touch the line with your hand.
Setup & Standards
- Equipment: barbell with plates for 5 weights (or a partner to change plates), and two lines 15 ft apart.
- Ground-to-overhead: any method from the floor to locked out overhead.
- No-touch shuttle run: both feet cross the line; hands don’t touch the floor.
- Score: total ground-to-overhead reps + shuttle runs across all 5 sets.
Meet the ZOAR Fitness Team
Our Programming.
Tailor-Built for You.
45-minute 1-on-1 call
$75, credited to your first month
What’s included →
Trail Blazer FAQ
What is the Trail Blazer WOD?
Trail Blazer: 5 sets of 2:00 on, 1:00 off with ground-to-overhead from heavy to light and max shuttle runs.
What is a good time for Trail Blazer?
Target: finish every barbell set with time left to run.
What does Trail Blazer test?
Trail Blazer tests strength under fatigue, barbell cycling and repeat sprint capacity.
How do I scale Trail Blazer?
Scale so every set leaves at least 45 seconds of shuttle runs.




